glamoxyn

Start with what the listener will hear

Microphone choice and mixing are covered in earlier parts of this series. This note picks up at the last stretch of the chain: monitoring, level checks and the final feed. The aim is simple. What the audience hears at home or in the hall should match what you intended in the control room.

Before anything is switched on, decide who the final feed is for. A television gallery, a venue's PA system and a streaming encoder each expect different levels, different loudness targets and sometimes a different channel layout. Write the destination at the top of your run sheet, because every later decision depends on it.

Ask the production for its delivery requirements in writing. If none exist, agree a short list with the director: loudness target, stereo or surround, and who receives a clean mix without commentary. Ten minutes on the phone in mid autumn rehearsal week saves an argument during transmission.

  • Name every destination of the feed on the run sheet
  • Get delivery levels and channel layout in writing
  • Agree who receives a clean mix and who receives commentary

Set up monitoring you can trust

Your ears are the final meter, so give them a fair test. Use the same headphones and the same speaker position for rehearsal and transmission. Changing either between the two means you are judging a different mix without knowing it.

In a studio gallery, place the nearfield speakers so the mixer sits in the middle of the stereo image, roughly equal distance from each. Keep the volume at a steady, moderate level and mark the dial position with tape. Listening louder than usual makes everything sound better than it is, and the mix will disappoint on quieter equipment.

On location, a closed-back headphone pair is often the only reliable reference, because the hall itself is part of the problem. Check the headphone feed on its own before the doors open, and confirm that talkback and programme audio are not leaking into each other.

  • Use the same headphones for rehearsal and transmission
  • Mark the monitor volume dial and leave it alone
  • Test talkback separately from programme audio

Walk the signal path from source to feed

Most faults on the day are found by following the signal in order rather than guessing. Start at the microphone and move one stage at a time: capsule, cable, stage box, preamp, desk channel, group, main output, then whatever carries the feed away from the desk.

At each stage, ask someone to speak or play a steady tone and watch the meter. You are looking for the point where the level jumps, drops or picks up noise. A cable with a worn connector will usually show itself as a crackle when it is moved gently, so ask a colleague to flex the run while you listen.

Keep a short log of what you find. When the same radio microphone packs fail twice in a week, the log makes the case for replacing them. Without it, the problem is only a memory and a feeling.

  • Check one stage at a time, in order
  • Use a steady tone or a spoken count at each stage
  • Keep a dated log of faults and fixes

Set levels with headroom, not heroics

A healthy mix leaves room above the loudest moment. Digital desks clip hard and without warning, and a clipped recording cannot be repaired afterwards. Aim for average speech sitting comfortably below the top of the meter, so a laugh or an applause burst does not push the main output into red.

Set the gain on each microphone while the speaker talks at the volume they will use on air, not at the soft level they use when asked for a sound check. Presenters often raise their voice once the lights come up, so ask for a second check with the cameras live.

Use a limiter on the main output as a safety net, but do not rely on it to carry the mix. If the limiter works constantly, the gain further back is wrong and the sound will pump audibly. Treat it as insurance for the unexpected, never as part of the plan.

  • Leave headroom for applause and laughter
  • Check gain again once the lights and cameras are live
  • Use the limiter as a safety net only

Hand over a clean final feed

The handover is where good work is lost. Before transmission, send a tone at the agreed reference level to the receiving point and ask them to confirm what they see on their meters. Matching numbers at both ends tell you the path is correct, and mismatched numbers tell you where to start looking.

Confirm the channel order as well. A left and right swap is easy to miss and quickly noticed by viewers. Speak a short test phrase while panning it hard left, then hard right, and have the receiving end say which side they heard it on.

Agree a simple way to speak to each other during the programme. A dedicated line to the gallery, with one named contact, is better than shouting across a crowded room. Note that contact's name and extension on the run sheet beside the feed's destination.

  • Send reference tone and compare meters at both ends
  • Confirm left and right with a spoken panning test
  • Name one contact at the receiving end

After the programme: record what worked

Once the feed has gone, spend a few minutes while everything is still set up. Save the desk scene or settings file with a clear name, and note which microphones were used, where they were placed and what level they ran at. Next time, the same room or the same presenter should start from this, not from zero.

Listen back to a short section of the recording on different equipment: studio speakers, headphones and, if you can, a cheap pair of earbuds. Problems that hide on good monitors often show on the small ones, and the small ones are what many viewers use.

Share your notes with the crew in plain language. A single page covering what changed, what failed and what to do differently becomes the starting point for the next job. That page is the most useful thing a sound engineer leaves behind.

  • Save desk settings with a clear name
  • Listen back on at least two kinds of speaker
  • Write one page of notes for the next crew

Good audio at the end of the chain comes from habits, not equipment: a fixed listening position, a signal path walked in order, honest headroom, a handover confirmed by numbers and notes kept for next time. None of it is complicated, but all of it has to happen before the cameras roll. If your crew would like a second pair of ears on its audio workflow, we are glad to talk it through.