glamoxyn

Choosing microphones by habit rather than by room

The most frequent mistake I see on shoots is a microphone chosen because it was in the kit last time. A presenter in a hard-walled studio and a presenter on a draughty stage need different capture, yet the same capsule often turns up for both. The result is thin speech, picked-up reflections or a handling noise that nobody noticed until the edit.

Walk the space before you decide. Clap once and listen to how long the room rings. Note where air handling, lighting dimmers and monitors sit, because all of them leak into a sensitive microphone. Then match the pickup pattern to the job: tight patterns for noisy stages, wider ones only where the room is genuinely quiet and treated.

It also helps to ask the director how close the camera will frame the speaker. A wide shot rules out a lavalier hidden in clothing less often than people think, but it does rule out a boom hanging in the picture. Settling this early saves an awkward argument on the day.

  • Listen to the room before choosing a pickup pattern
  • Note every noise source near the talent position
  • Confirm framing with the director before rigging booms

Setting gain late and trusting the meters alone

Gain staging is the quiet foundation of every mix, and it is routinely left until the last ten minutes. When the first input is set too low, the whole chain compensates by lifting later stages, and the noise floor comes up with it. When it is set too hot, a single laugh from a guest clips the feed and the damage cannot be repaired downstream.

Set levels with the person speaking at the volume they will really use in transmission, not at a polite rehearsal murmur. Leave generous headroom on the early stages and bring the level up gradually through the chain, checking each point rather than only the final meter.

Meters are a guide, not a verdict. A signal can read comfortably and still sound harsh or boxy. Put on headphones, listen to each source on its own, and only then judge it against the others.

  • Set gain with talent speaking at full programme volume
  • Keep headroom at every stage, not just the output
  • Check by ear as well as by meter

Leaving monitoring as an afterthought

A mix is only as good as what the engineer can hear it on. Crews often spend careful hours on capture and then monitor through whichever speakers or headphones were nearest. Decisions made on an unreliable monitor feel right in the gallery and sound wrong on a living-room set.

Pick one trusted monitoring setup and keep it consistent across the job. Check the mix at a low level as well as a loud one, because most viewers listen quietly. If the programme will be heard on small speakers, step through a pair of those before you commit.

For live events, remember that the front-of-house sound and the broadcast feed are two different mixes. Treating them as one means the feed inherits the room's boom and bass, and the home audience hears a muddy programme.

  • Use the same monitors throughout the job
  • Listen at low level before approving a mix
  • Keep the broadcast mix separate from the house mix

Ignoring phase, polarity and radio frequency clashes

Two microphones picking up the same voice can cancel each other and leave a hollow, distant sound that no equaliser fixes. This happens most often when a lavalier and a boom are both open on one speaker, or when polarity is reversed in a long cable run. A quick test with a single voice and a polarity switch usually reveals the problem in seconds.

Radio microphones bring their own trouble. Frequencies that worked at one venue may be crowded at the next, and a clash shows up as dropouts at the worst moment. Scan the site before rigging, label each pack with its channel, and keep spare batteries where the engineer can reach them.

Write the frequency plan down and share it with anyone else using wireless gear on site, from camera crews to the lighting team. A clash is much easier to prevent by talking than to chase while the show is running.

  • Test polarity with one voice before opening a second microphone
  • Scan for clear frequencies at every new venue
  • Share the wireless plan with all crews on site

Skipping a full run of the final feed

Audio can sound fine in the room and still fail on its way to the viewer. A dropped embedded channel, a swapped left and right, or a feed sent at the wrong level can all slip through when nobody tests the complete path from microphone to transmission.

Build a short end-to-end check into every rehearsal. Send tone and speech from the source, follow it through the desk and the routing, and confirm with the person receiving the feed that it arrives clean, in the right channels and at the right level. Do it again after any change to the setup.

Agree beforehand who talks to whom if something goes wrong. A clear line between the audio position and the gallery turns a potential panic into a thirty-second correction.

  • Test tone and speech along the whole signal path
  • Repeat the check after every change to the rig
  • Agree a talkback line between audio and gallery

Writing nothing down for the next crew

The last mistake is not technical. Settings, input lists and channel names live in one engineer's head, and when that person is absent the next team starts from nothing. Small differences, such as a different patch or a changed microphone, then produce the same problems all over again.

A single page is enough. Record the input list, the microphone and its position, the gain settings, the monitoring arrangement and any quirks of the room or venue. Keep it with the production files and bring it out at the start of the next job.

This is also where a workflow review pays for itself, because it turns private habits into shared practice. Even without outside help, a written note after each production is the cheapest improvement most crews can make.

  • Record inputs, positions and gain settings after each job
  • Note venue quirks while they are fresh
  • Store the page with the production files

None of these mistakes needs expensive equipment to fix. They come down to listening to the space first, setting levels with care, monitoring honestly, planning radio use, testing the whole path and writing down what worked. As the evenings draw in and indoor shoots and events fill the diary, it is a good moment to review your own audio routine before the busy weeks begin.